Download Now
Mimaki JV2-130 Printer Driver

Not to be outdone, Mimaki rolled out to the graphic arts market its seven-color piezoelectric JV, the first seven-color, large-format printer. Like the Roland. Results 1 - 48 of 65 - Mimaki Ink Cartridge Mild Solvent 2 JV2 JV3 Series Light Magenta Spc- Mimaki CJV, CJV, CJV, CJV MIMAKI JV, DPI. Zalewaja1 Mimaki LED UV Printer, The worlds most profitable printer.


MIMAKI JV2-130 PRINTER DRIVERS DOWNLOAD FREE

Type: Driver
Rating:
3.38
210 (3.38)
Downloads: 529
File Size: 23.60Mb
Supported systems: Windows 2008, Windows XP, Windows Vista, Windows 7/8/10
Price: Free* [*Free Registration Required]

Download Now
Mimaki JV2-130 Printer Driver

With the shaft of the frame as the fulcrum, turn over the maintenance cover toward the front so that it is placed in the vertical position.

MIMAKI JV2-130 PRINTER DRIVER FOR PC

Pull out the maintenance cover upward. The wiper wipes off the ink adhering to the surface of nozzles. As the printer is used, the wiper and ink caps gradually become stained with ink and Mimaki JV2-130 Printer.

Page 4 Daily Maintenance Open the right maintenance cover. Pull out the wiper by holding the projections at both ends.

Remove the ink from the wiper and the bracket using a cotton swab dampened with Mimaki JV2-130 Printer cleaning solution. Replace the wiper with a new one if it is badly soiled or curled.

For Mimaki JV2-130 / JV2-90 / TX1 print head dx2 printer nozzle

To replace the wiper, terminate the work instructed here first and then follow Mimaki JV2-130 Printer wiper replacement procedure. Be careful of the direction of the wiper. Wipe off ink or dirt adhering to the rubbers of the caps and the wiper cover using a cotton swab dampened with the cleaning solution.

Remove the ink from the wiper, bracket and the vicinity of the wiper insertion hole using a cotton swab dampened with the cleaning solution. Page 4 Daily Maintenance Mimaki JV2-130 Printer the caps with the cleaning solution using a dropper.

Solvent Inks Mimaki JV3 Series

Fill a cap with washing liquid fully Fill the liquid. Normally set 1 minute.

MIMAKI JV2-130 PRINTER DRIVER FREE

Take the cleaning solution into the dropper. During a pause of idle suction, drop cleaning liquid into a cap until just before it starts overflowing from the cap.

MIMAKI JV2-130 PRINTER MAC

Repeat dropping the cleaning liquid into each of the other caps the same way. Page 4 Daily Maintenance Pull out the wiper by holding the projections at both ends. See After cleaning the wiper, install it in position by Mimaki JV2-130 Printer the projections at both ends. Page 4 Daily Maintenance Open the maintenance cover, and fill the caps with the cleaning solution using a dropper. Since the printer performs idle suction operation intermittently, repeat this work several times to clean the ink discharge passage.

Perform this operation with all the caps.

Filling the tubes with the cleaning solution [MaintWashLiquid] Supply and discharge the cleaning liquid for the wiper and pump tubes. If there is a Mimaki JV2-130 Printer with the waste ink tank, the display will show either of the following messages.

Once the cartridge is installed, the supply of the cleaning liquid will start. Cleaning liquid is drawn up and the tubes are filled with the cleaning liquid.

WASATCH SOFTRIP MIMAKI EXCLUSIVE EDITION - WASATCH - Stanford Marsh Group Graphics

Go to step 6 when Mimaki JV2-130 Printer cleaning liquid is to be supplied for the first time or to step 9 when it is to be supplied after the discharge of the old cleaning liquid. Remove a filling Set a washing up cartridge. By driving the cleaning liquid suction pump, wash the ink caps, ink exhaust passages, and the inside of the tubes of the ink suction pumps.

Washing will not be started if the cleaning liquid has not been supplied or if a warning is generated for the cleaning liquid cartridge or waste ink tank. Wiper Cleaning 4 Daily Maintenance Wiper Mimaki JV2-130 Printer Bring the wiper into the wiper box and wash the wiper.

Mimaki Gumtree Australia Free Local Classifieds

Washing will not be started if the cleaning liquid has not been supplied or the Mimaki JV2-130 Printer liquid cartridge has not been installed. Page Wiper cleaning Open the right maintenance cover. Page 4 Daily Maintenance Wipe off ink or dirt adhering to the wiper cover using a cotton swab dampened with the cleaning solution. Be careful not to leave lint of the cotton swab.

Lint may cause Mimaki JV2-130 Printer failure.

Related Posts